Albrecht AE 500 H First Edition Manual do Proprietário descarregar pdf

AX400 / AE 500 H First Edition

Owner’s Manual

Thank you for purchasing our receiver

For proper use of this receiver, please read this manual thoroughly.

Keep this manual in a safe place for future reference.

WARNING

l Do not use any batteries other than size AA Alkaline or manganese batteries. Using different batteries could

cause fire, electric shock or failure.

l Do not place consumed batteries in a fire. They could explode, causing fire or burns.

l Do not install or remove batteries while your hands are wet. This could cause electric shock.

l In the event that smoke is emitted, a strange odor or noise is generated, or similar abnormality occurs, it could

cause fire, electric shock or breakdown. Consult your dealer immediately for the necessary instructions or

repair needed.

l Do not attempt to repair the receiver yourself. Doing so may lead to serious damage or physical injury.

l Do not attempt to disassemble or modify this product in any way. This could lead to fire, electric shock or

breakdown.

CAUTION

l Do not use this product for anything other than a receiver.

l When not in use, keep it out of the reach of infants and small children.

l During extended trips or other times when this product is not in use for long periods, take the batteries out.

Keep the batteries stored in a safe place and out of the reach of infants and small children.

l Discontinue use of this product if it has a negative influence on TV, electronic device, therapeutic devices and

or other equipment.

l Always be aware of antenna location to avoid personal injury.

l When conducting routine maintenance, be sure to disconnect the power for additional safety.

l Do not place this product in locations with extreme temperature, high humidity or excessive dust. Do not keep

it in an automobile. It could lead to fire, electric shock or breakdown.

NOTICE

Unauthorized use of the contents of radio communications or divulging its contents to other parties is prohibited by

law.

INTRODUCTION

1 2 3 4 5 6 ... 17 18

Owner’s Manual 1
REFERENCES 17

Resumo do Conteúdo

Página 1 - Owner’s Manual

AX400 / AE 500 H First EditionOwner’s ManualThank you for purchasing our receiverFor proper use of this receiver, please read this manual thoroughly.K

Página 2

Using a One Touch SearchIn this mode, you are able to set upper and lower limits of frequencies to be searched between. The 10 setsfrequencies (20 fre

Página 3

Erasing the Search Band Channel MemoryThe frequencies entered in Search Band Channel Memory can be erased.1. Set the unit to the Channel Memory Mode b

Página 4

appears on the display.2. Hold down FUNC key and press 7 FREQ/CH key once again.3. Select the channel memory address to be erased by using the selecto

Página 5

Scanning A Block of Channels (Block Scan)You can scan through only specified block of channels. One block consists of 100 channel memory addresses. (

Página 6

TO USE YOUR RECEIVER MORE EFFECTIVELYIn order to use your receiver more effectively, the unit enables you to change various settings. All these functi

Página 7

To complete the setting, press CLEAR PROGRAM key.Changing Light OperationThe light stays on for 5 seconds after the Light key is released. The Light

Página 8

To activate the programmed SET MODE, simply hold down FUNC key and press 4 MY key. The value of the settingsare changed by repeating the action. When

Página 9

Changing the Frequency to MHz Digit (Fast Step)In order to change the frequency rapidly, this receiver is equipped with FAST STEP function. This is ac

Página 10

The channel memory is not stored. There are no vacant channel Memory addresses.Does not scan/ search. Squelch is off.Not able to scan Channel Memorie

Página 11

l Never disassemble the receiver. Never touch the receiver’s core.l It is adjusted for optimum performance.l Avoid hot places and locations exposed t

Página 12

by the POWER key. Please take out the batteries and replace them!Adjusting the Volume To increase the volume, turn the VOL knob clockwise. (Illu

Página 13

(Illust. 13-2) Hold down FUNC key and press POWER key. (A high pitched beep is emitted). Release the keys and confirm if the original state is displ

Página 14

l Pressing this key while the FUNC key is pressed activates the light. 2 MODE Keyl Enters numeric „2“.l Pressing this key while the FUNC key is presse

Página 15

Confirm the display. If M is displayed, press CLEAR PROGRAM key. (When ‘M’ is displayed, you are in the Channel Memory Mode. ) Use rotary selector to

Página 16

How to Recall the Channel Memory [1]The frequencies that have previously been programmed into channel memories can be recalled by using followingmetho

Página 17 - REFERENCES

4. To complete this procedure, press CLEAR PROGRAM key.Note:l All the contents of channel memories are cleared during All Reset procedure even when th

Página 18

Search and Scan FunctionSearch and Scan Functionl In the Expanded Mode, in order to search for the desired frequencies, Search and Scan functions are